Schulung Automatisierung

Automa­tion training

In our train­ing cours­es, you ben­e­fit from the many years of prac­ti­cal expe­ri­ence and the knowl­edge of our broad-based team in the field of automa­tion. We offer train­ing on the lead­ing con­trol man­u­fac­tur­ers list­ed below as well as indi­vid­ual train­ing on oth­er man­u­fac­tur­ers. Con­tact us and togeth­er we will design a train­ing course tai­lored to your requirements.


Par­tic­i­pants should have a basic knowl­edge of elec­tri­cal engi­neer­ing, ana­logue and dig­i­tal tech­nol­o­gy and con­trol tech­nol­o­gy as a prerequisite.


As a solu­tion and coop­er­a­tion part­ner, we cov­er a wide range of Siemens train­ing cours­es. We are one of the few com­pa­nies in Ger­many that still offer S5 train­ing. An impor­tant point in staff devel­op­ment is often train­ing for the tran­si­tion from one soft­ware gen­er­a­tion to the next. There­fore, in addi­tion to S7 and TIA train­ing, we also have a spe­cial tran­si­tion train­ing in our portfolio.

In addi­tion to the clas­sic PLC train­ing cours­es, we also offer a sep­a­rate TIA Safe­ty train­ing course, as well as WinCC SCA­DA sys­tem and PCS7 training.

Contents include:
  • Intro­duc­tion to the respec­tive prod­uct family
  • Basics of the dif­fer­ent pro­gram­ming lan­guages (includ­ing FBD, LD and IL)
  • Vari­ables, data and data types
  • Data blocks
  • Code com­po­nents
  • Pro­gram­ming and pro­gramme structure
  • Doc­u­men­ta­tion and commenting
  • Test and diag­nos­tic functions
  • Visu­al­i­sa­tion

In all train­ing cours­es, the con­tent is taught using prac­ti­cal exam­ples and pro­gram­ming exercises.

  • S7 Basic / Advanced / Intensive
  • S7 fail-safe control
  • S7 changeover to TIA (incl. migration)
  • Siemens TIA Portal
  • Siemens TIA Safety
  • Siemens WinCC SCA­DA System
  • SCL inten­sive training
  • PLC for trainees
  • PCS7
  • S5 Basic / Advanced / Intensive


For Beck­hoff we offer train­ing for Twin­CAT 2 as well as for Twin­CAT 3. In addi­tion, we offer a sep­a­rate safe­ty train­ing includ­ing Safe Motion for Beckhoff.

  • Twin­CAT 2
  • Twin­CAT 3
  • Twin­SAFE (also SafeMotion)


Qual­i­ty Automa­tion GmbH has been a pre­mi­um sys­tem part­ner of Mit­subishi since 2007. Our train­ing cours­es here are very strong­ly cus­tomer-ori­ent­ed and are geared entire­ly to your require­ments and focal points. Is it a changeover from anoth­er man­u­fac­tur­er to Mit­subishi? Is the focus on dri­ves or decen­tralised periph­er­als? Or is it about robot­ics programming?

From the old­er FX series to the Q series to the lat­est iQ‑R series, our staff are famil­iar with Mit­subishi controllers.

  • iQ Works 2&3 (includ­ing GX Works 2&3)
  • GX Devel­op­er
  • FX Series
  • Q‑Series
  • iQ‑R Series (C‑Controller)

Our training offer

Schulung Automatisierung
Automa­tion training 

In our train­ing cours­es, you ben­e­fit from the many years of prac­ti­cal expe­ri­ence and the knowl­edge of our broad-based team in the field of automation.

Learn more 

Con­tact us with­out obligation
for an indi­vid­ual offer!